Uses

• To obtain a concrete of quality, compactness, durability and strength.
• To obtain a concrete with excellent workability by reducing the proportion of mixing water and improving workability.
• Specially designed for use in ready-mixed concrete plants and civil works.

Advantages

• Strong water reduction: between 15 and 20% depending on the dosages used.
• Reduces permeability and water penetration in concrete.
• Provides water-repellent properties to the concrete.
• The incorporation of new synthesis molecules notably improves the appearance and compactness of the concrete.
• The plasticising effect is maintained, even in hot climates.
• Minimises concrete shrinkage as it allows working with lower water/cement ratios.

Standards

Auramix 230 complies with UNE-EN 934-2:2010 Table 2 as a water/plasticiser reducer.

Description

Auramix 230 is a multifunctional, high-end, synthetic polymer-based plasticiser for ready-mixed concrete with high water-reducing and cement particle dispersing properties. It maintains the workability of concrete longer than conventional plasticisers.

Typical dosage

The optimum dosage of Auramix 230 to achieve specific requirements should be determined by tests using the materials and conditions that will be tested in practice.

A starting point for such trials is to use a dosage of 0.3-1.1 litres per 100 kg of cementitious material, including ash, slag or microsilica.

Properties

The following results were obtained at a temperature of 20ºC:

• Appearance: light golden liquid
• Density: 1,06 ± 0,01 kg/l
• pH: 5,5 ± 1,0
• Water soluble chloride content (CI-): ≤ 0,10%.
• Alkali content (Na2O equivalent): max. 6 % by mass
• Primary function: To increase workability
• Secondary function: Increase mechanical strength

Mode of use

Mixing design

Once the appropriate dosage has been selected, care must be taken to ensure the consistency of the materials used and the mixing processes.

the materials used and the mixing and distribution processes.

Compatibility

Auramix 230 is compatible with other Fosroc Euco admixtures used in the same concrete mix. If more than one admixture is used, they should be added to the concrete separately and not mixed together prior to being added. The resulting properties of concrete containing more than one admixture must be checked by prior testing.

Auramix 230 is suitable for use with all cements complying with RC-08.

Dosing system

The correct quantity of Auramix 230 should be measured by means of a suitable dosing system. For best results, the admixture should be added to the concrete in the mixing water or directly into the mixer at the same time as the water. Contact the Fosroc Euco Technical Department for advice on the appropriate dosing equipment and its installation.

Effects of overdosage

An overdosage of twice the maximum dosage indicated may cause a delay in the setting of the concrete as well as an additional air lock.

Curing

The final characteristics of any structural concrete will depend on good curing practice. It is therefore very important to use a Fosroc Euco Concure curing membrane, water spray or wet burlap.

Clean-up and disposal

Spills of Auramix 230 should be absorbed with sand or earth and transferred to suitable containers. Product residues should be flushed away with large quantities of water. Disposal of the product and packaging is the responsibility of the end user.

Storage

Auramix 230 has a storage period of 12 months if kept in a dry place and in its original, closed containers at a temperature between 2ºC and 40ºC.

Freezing point: -3°C approx.

Precautions

Safety and Hygiene

Auramix 230 must not be swallowed or come into contact with skin and eyes. Wear protective gloves and goggles. Splashes on the skin should be washed off with water. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.

If swallowed, seek immediate medical attention. Do not induce vomiting.

For further information see Material Safety Data Sheet.

Fire

Auramix 230 is not flammable.