Conplast MR285 - Multi-range water-reducing plasticiser for ready-mixed concrete
Multifunctional plasticising additive for the production of high-end plant concrete, based on synthetic and natural polymers, for the production of ready-mixed concrete, with high water-reducing and cement particle dispersing properties.
Consumption: 0.3 - 1% of the weight of the cement.
(CONFIRM MANUFACTURING TIME)
MORE THAN 20 YEARS OF EXPERIENCE
SHIPPING IN 48-72 HOURS
100% SECURE PAYMENT
Uses
- To obtain a concrete of quality, compactness, durability and resistance.
- To obtain a concrete with excellent workability by reducing the proportion of mixing water and improving workability.
Advantages
- Strong water reduction: between 15 and 20% depending on the dosages used.
- Reduces the permeability and penetration of water into the concrete.
- Provides water-repellent properties to the concrete.
- The incorporation of new synthesis molecules notably improves the appearance and compactness of the concrete.
- The plasticising effect is maintained, even in hot climates.
- Minimises concrete shrinkage as it allows working with lower water/cement ratios.
Standards
Conplast MR285 complies with UNE-EN 934-2:2010 Table 2 as a water reducer/plasticiser.
Description
Conplast MR285 is a multifunctional, high-end plasticiser based on synthetic and natural polymers for ready-mixed concrete with high water-reducing and cement particle dispersing properties.
Typical dosage
The optimum dosage of Conplast MR285 to meet specific requirements should be determined by tests using the materials and conditions that will be tested in practice.
A starting point for such trials is to use a dosage of 0.3-1.0 litres per 100 kg of cementitious material, including ash, slag or microsilica.
Properties
The following results were obtained at a temperature of 20ºC:
- Appearance: Dark brown liquid
- Density: 1,185 ± 0,01 kg/l
- pH: 3,5 ± 1,0
- Water soluble chloride content (CI-): ≤ 0,10%.
- Alkali content (Na2O equivalent): max. 5 % by mass
- Primary function: To increase workability
- Secondary function: Increase mechanical strength
Mode of use
Mixing design
Once the appropriate dosage has been selected, care must be taken to ensure the consistency of the materials used and the mixing and spreading processes.
Compatibility
Conplast MR285 is compatible with other Fosroc Euco admixtures used in the same concrete mix. If more than one admixture is used, they must be added to the concrete separately and not mixed together prior to being added. The resulting properties of concrete containing more than one admixture must be checked by prior testing.
Conplast MR285 is suitable for use with all cements complying with RC-08.
Dosing system
The correct quantity of Conplast MR285 should be measured by means of a suitable dosing system. For best results, the admixture should be added to the concrete in the mixing water or directly into the mixer at the same time as the water. Contact Fosroc Euco's Technical Department for advice on the appropriate metering equipment and its installation.
and its installation.
Effects of overdosage
An overdosage of twice the maximum dosage indicated may cause a delay in the setting of the concrete as well as an additional air lock.
Curing
The final characteristics of any structural concrete will depend on good curing practice. It is therefore very important to use a Fosroc Euco Concure curing membrane, water spray or wet burlap.
Clean-up and disposal
Spills of Conplast MR285 should be absorbed with sand or earth and transferred to suitable containers. Product residues should be flushed away with a large amount of water. Disposal of the product and packaging is the responsibility of the end user.
Storage
Conplast MR285 has a storage period of 12 months if kept in a dry place and in its original, closed containers at a temperature between 2ºC and 40ºC.
Freezing point: -3 ºC approx.
Precautions
Safety and Hygiene
Conplast MR285 must not be swallowed or come into contact with skin and eyes. Wear protective gloves and goggles. Splashes on the skin should be washed off with water. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
If swallowed, seek immediate medical attention. Do not induce vomiting.
For further information see Material Safety Data Sheet.
Fire
Conplast MR285 is not flammable.
You might also like